Kmc-controls FlexStat Operation Guide User Manual download pdf (Page 5)

FlexStat 5 Operation Guide, Rev. R

WED 11/19 3:22 PM

COOL:

OCC:

FAN:

HUM: 37% RH

WED 11/19 3:20 PM

COOL:

OCC:

FAN:

HUM: 36% RH

WED 11/19 3:20 PM

COOL:

OCC:

FAN:

HUM: 36% RH

WED 11/19 3:20 PM

COOL:

OCC:

FAN:

HUM: 36% RH

WED 11/19 3:20 PM

COOL:

OCC:

FAN:

HUM: 36% RH

WED 11/19 3:20 PM

COOL:

OCC:

FAN:

OUTSIDE: 56° F

WED 11/19 3:20 PM

COOL:

FAN:

HUM: 36% RH

WED 11/19 3:22 PM

COOL:

OCC:

FAN:

HUM: 37% RH

Display Options

To toggle the displayedtemperaturescale between

Fahrenheit and Celsius, press the Enter buon for at

least two seconds until the desired scale is displayed.

(Pressing Enter for less time will turn on the back-

light if it is o.) The desired scale will persist on the

display until this process is repeated or the FlexStat

is restarted.

After a restart, the temperature scale will revert to

whatever scale is set in the Application menu. To

change the scale so that it persists after restarting,

change it in the Application menu by reseing the

selected application to Not Congured, changing

the temperature scale, and then reconguring all the

application options. See (Advanced) Application and

Additional Setup on page 7).

Fahrenheit decimal values are not displayed by de-

fault but can be enabled in the User Interface menu.

See Show Temperature Tenths (Decimals) on page

21.

With R2.0.0.13 and later rmware, Fahrenheit tem-

perature values on the display change in whole

degree increments by default, and Celsius values

change in 0.5° increments. Changing the default No

to Yes will show tenths of a degree values for both

scales.

This does not aect setpoint adjustments, which are

always in whole degree increments for Fahrenheit

and half degree increments for Celsius.

WED 11/19 3:22 PM

COOL:

OCC:

FAN:

HUM: 37% RH

When DisplayBlanking is enabled, the display

turns o at the same time the backlight goes o

(after reset, initial power-up, or time-out). When any

buon is pressed, the display will reappear until the

time-out is reached again. See Display Blanking on

page 21.

Hospitalitymode has a simpler display and limited

menus, and it is typically used in hotel rooms. Users

typically can change only the setpoint, system mode,

and fan speed. Pushing the Left and Right buons

displays customizable menu selections. See Mode on

page 21.

By default, rotationvalues in the lower right of the

screen show relative humidity and/or CO

levels in

models with the relevant optional sensors. If more

than one value is shown, the values will rotate ap-

proximately every ve seconds.

These values can be hidden if desired, and additional

options are also available. See Rotation Values on

page 21.

NOTE: Displays can also be locked. LockedUI

mode appears like Standard mode on the

Home screen, but all buon functions

(except the backlight) are disabled. The

setpoint and other operation functions

cannot be changed by the user. See Mode on

page 21.

NOTE: The contrast of the LCD display can also be

adjusted. See Contrast on page 21.

WED 11/19 3:20 PM

COOL:

OCC:

FAN:

HUM: 36% RH

COOL:

OCC:

FAN:

HUM: 36% RH

DateandTime Display are enabled by default, but

they can be turned o and replaced by a rotating

clock icon. See Show Time and Date on page 21.

1 2 3 4 5 6 7 8 9 10 ... 45 46

Comments to this Manuals

No comments

Kmc-controls FlexStat Operation Guide User Manual Page 5

Comments to this Manuals

Related products and manuals for Sensors Kmc-controls FlexStat Operation Guide